Before you begin to take cuttings, it is a good idea to have all the equipment ready and in good working order. All equipment should be thoroughly cleaned and the cloning area should be as sterile as possible.
Step 1. Rinse the propagation blocks with a half strength nutrient solution to which has been added 4 drops of pH lower per two litres. Let propagation blocks soak for up to 10 hours prior to cloning in this solution. Discard soaking solution and just prior to cloning rinse blocks again with 4 litres of half strength warmed nutrient solution to which has been added 4 drops of Rootzone Accelerant and 5 drops of Superthrive. Insert thermometer into cubes and allow temperature to reach the green zone before cloning commences. Temperature should be maintained day and night within the range of 20 to 30 Cent if cloning is to be successful.
Step 2. Select cuttings - cuttings can be taken from anywhere on the mother plant provided the stem is of the correct thickness. Stem thickness should be between 4mm to 6mm diameter. Take cuttings with about four sets of well developed leaves and approx 100mm to 150mm in length. The topmost growing shoots make excellent cuttings however make sure the wood is of the correct thickness and not too green or to woody. You may wish to take a number of cuttings at one time immerse them in an ice cream container, or similar, filled with tepid water to which you have added a few drops of superthrive anti-stress formula.
Step 3. Take the single edged razor blade and begin trimming your cuttings. Take cuttings one at a time from tepid water and now trim bottom two sets of leaves flush with stem. Trim approx 50% of leaves by cutting across the leaf surface. It is hard for the cutting to keep these large leaves alive and they usually wilt and fall off if not cut in half. Cut the stem at fourty five degrees across the bottom leaf nodes. Gently scrape the cut area around the bottom of the stem. This disrupts the cells on the stem surface and helps them change into root cells. Take whatever rooting hormone you have purchased and dip the bottom of stem into your rooting compound. Here is a tip: Do not dip directly into rooting hormone bottle instead pour some off into a small container such as a thimble and discard what is not used. This saves you introducing any bacteria or disease into main container. Store main bottle of rooting hormone if refrigerator after opening.
Step 4. Now you are ready to put the cuttings into the growool propagation blocks. Gently insert the stem into the cube making sure the stem does not protrude out of the bottom of the cube. After all the clones have been prepared and placed in the propagation blocks you may water the block again with half strength nutrient solution to which you have added Superthrive and Root Zone Accelerant. Water the blocks until nutrient freely runs from the blocks allow to drain for a few minutes then place blocks inside the cloning chamber and place the chamber over the heating pad. You should close the vents on the grow top for the first 3 days. Check moisture and temperature for the first couple of days and mist cuttings morning and night with water to which you have added a couple of drops of Superthrive. Be careful to ensure that you do not have water sitting in bottom of tray. Growool cubes should be able to freely drain at all times. Place cloning chamber under flourescent fixture for approx 16 - 18 hours per day.
Step 5. After three days open the vent on the Grow Top. Monitor progress of clones for another 4 to 5 days by this stage it should be time to take Grow Top off the unit and expose clones to normal air - still continue misting morning and evening. Again monitor nutrient and moisture levels in the propagation block. By the end of a further 5 to 8 days you should be able to see root hairs protruding from the propagation blocks. Healthy roots look thick, white and hairy. Sickly roots look thin, yellowish or brown and hairless. The clones with the healthiest roots will be the same ones you will be proud of at harvest time.
Step 6. When your cuttings are well rooted and have begun to shoot it is time to transplant them into you growing system. Slowly introduce them to full strength nutrient and place them under a H.I.D. light system. Remember the new clones are tender and exposing them rapidly to a full strength H.I.D. lamp after the fluros would be a shock. Care should be taken to acclimatise your new clones to the brighter light. Start by raising the H.I.D. lamp approx one metre above the clones for the first few days slowly lower the lamp over the next week till the lamp is at the correct height. This will ensure a smooth stress free transition to growing under H.I.D. lamps.
Step 1. Rinse the propagation blocks with a half strength nutrient solution to which has been added 4 drops of pH lower per two litres. Let propagation blocks soak for up to 10 hours prior to cloning in this solution. Discard soaking solution and just prior to cloning rinse blocks again with 4 litres of half strength warmed nutrient solution to which has been added 4 drops of Rootzone Accelerant and 5 drops of Superthrive. Insert thermometer into cubes and allow temperature to reach the green zone before cloning commences. Temperature should be maintained day and night within the range of 20 to 30 Cent if cloning is to be successful.
Step 2. Select cuttings - cuttings can be taken from anywhere on the mother plant provided the stem is of the correct thickness. Stem thickness should be between 4mm to 6mm diameter. Take cuttings with about four sets of well developed leaves and approx 100mm to 150mm in length. The topmost growing shoots make excellent cuttings however make sure the wood is of the correct thickness and not too green or to woody. You may wish to take a number of cuttings at one time immerse them in an ice cream container, or similar, filled with tepid water to which you have added a few drops of superthrive anti-stress formula.
Step 3. Take the single edged razor blade and begin trimming your cuttings. Take cuttings one at a time from tepid water and now trim bottom two sets of leaves flush with stem. Trim approx 50% of leaves by cutting across the leaf surface. It is hard for the cutting to keep these large leaves alive and they usually wilt and fall off if not cut in half. Cut the stem at fourty five degrees across the bottom leaf nodes. Gently scrape the cut area around the bottom of the stem. This disrupts the cells on the stem surface and helps them change into root cells. Take whatever rooting hormone you have purchased and dip the bottom of stem into your rooting compound. Here is a tip: Do not dip directly into rooting hormone bottle instead pour some off into a small container such as a thimble and discard what is not used. This saves you introducing any bacteria or disease into main container. Store main bottle of rooting hormone if refrigerator after opening.
Step 4. Now you are ready to put the cuttings into the growool propagation blocks. Gently insert the stem into the cube making sure the stem does not protrude out of the bottom of the cube. After all the clones have been prepared and placed in the propagation blocks you may water the block again with half strength nutrient solution to which you have added Superthrive and Root Zone Accelerant. Water the blocks until nutrient freely runs from the blocks allow to drain for a few minutes then place blocks inside the cloning chamber and place the chamber over the heating pad. You should close the vents on the grow top for the first 3 days. Check moisture and temperature for the first couple of days and mist cuttings morning and night with water to which you have added a couple of drops of Superthrive. Be careful to ensure that you do not have water sitting in bottom of tray. Growool cubes should be able to freely drain at all times. Place cloning chamber under flourescent fixture for approx 16 - 18 hours per day.
Step 5. After three days open the vent on the Grow Top. Monitor progress of clones for another 4 to 5 days by this stage it should be time to take Grow Top off the unit and expose clones to normal air - still continue misting morning and evening. Again monitor nutrient and moisture levels in the propagation block. By the end of a further 5 to 8 days you should be able to see root hairs protruding from the propagation blocks. Healthy roots look thick, white and hairy. Sickly roots look thin, yellowish or brown and hairless. The clones with the healthiest roots will be the same ones you will be proud of at harvest time.
Step 6. When your cuttings are well rooted and have begun to shoot it is time to transplant them into you growing system. Slowly introduce them to full strength nutrient and place them under a H.I.D. light system. Remember the new clones are tender and exposing them rapidly to a full strength H.I.D. lamp after the fluros would be a shock. Care should be taken to acclimatise your new clones to the brighter light. Start by raising the H.I.D. lamp approx one metre above the clones for the first few days slowly lower the lamp over the next week till the lamp is at the correct height. This will ensure a smooth stress free transition to growing under H.I.D. lamps.
No comments:
Post a Comment